Make Switchable Smart Glass Solution with Self-Adhesive Switchable Privacy Film
About SF Smart Film
Self-adhesive Smart Film is made of Protect Film, Adhesive Surface,
ITO Film, Liquid Crystal & Polymer. It works same resemblance
performances as the Privacy Glass made in laminating way with
NON-Adhesive Switchable Smart Film. Its very convenient and flexible
to install the SELF-ADHESIVE Switchable Privacy Film on the ALREADY
installed windows.
SELF-ADHESIVE SWITCHALBE PRIVACY FILM Performance Parameters
+Switch on :Transparent
+Switch off: Opaque
+Dimmer: Transparent - opaque ( AC 0~110 V)
+Power Consumption: SELF-ADHESIVE SWITCHALBE PRIVACY FILM has power
consumption about 6~7W/m2
+SELF-ADHESIVE SWITCHALBE PRIVACY FILM which is transparent or opaque,
excludes 99% outside UV Radiation.
Description Switch Data Description Switch Data
Milky White Film Transmittance On 87% Dark Gray Film Tramsmittance On 83%
Off 7% Off 7%
Haze On 5% Haze On 2%
Off 78% Off 87%
Operate Voltage 90V AC
UV Blocked 99%
Adhesive Strength 0.01N/cm
Standard Size
Application Ratio of W&L Specification Dimension Width*Length
Display 4/3 48 Inch 980mm*750mm
64 Inch 1300mm*980mm
16/9 79 Inch 1600mm*1200mm
96 Inch 2130mm*1200mm
Decoration and Indoor 980mm*3000mm
1200mm*3000mm
Equipment Required
- Self adhesive Switchable Film
- Window scraper / blade
- Hard rubber roller
- Soft edge squeegee
- Nitrile protective gloves
- LINT FREE Cleaning cloths
- Liquid glass polish
- IPA / Soft cloths
- 1.5mm electrical cable
- Cable strippers
- Soldering iron / solder
- Scissors / sharp blade
- Dow Corning silicone (7091)
- Plastic cover trim / clear double sided tape
PLEASE NOTE
- The External dimensions of the SELF-ADHESIVE Switchable Privacy Film
are 2 - 3mm smaller than the visual area of the windows.
- The BUS-BAR (electrical contact strip) should never contact with any
metal frame or trim.
STEP 1
Place the SELF-ADHESIVE Switchable Privacy Film in a safe clean table.
STEP 2
Make sure the CLING surface is facing up.
STEP 3
Spray the glass with LIQUID glass polish and use a window scraper or
blade to remove any dirt or blemishes from the glass surface.
STEP 4
Spray the glass with LIQUID glass polish and clean with a SOFT LINT-FREE cloth.
Then Using a LINT FREE cloth, wipe the glass surface with IPA
(Isopropyl Alcohol) and wait for EVAPORATE.
STEP 5
Wipe down the Protective Liner on the cling side of the SELF-ADHESIVE
Switchable Privacy Film to remove any dust.
STEP 6
Remove the first 100mm (4") of the protective liner covering the cling side on
the BUS-BAR edge.
Make sure that you do this in a clean dust free environment.
STEP 7
Remove the Protective Liner from the ADHESIVE STRIP on the BUS-BAR edge.
STEP 8
Make the BUS-BAR edge of the SELF-ADHESIVE Switchable Privacy Film
along with the top edge of the glass. When in position, run your
finger along the BUS-BAR to fix the top edge.
STEP 9
Gradually pull away the protective liner and allow the film to slowly
adhere to the glass surface under its own pressure.
Using the roller move down the film working in horizontal lines left
to right to disperse any air bubbles.
If any small bubbles are visible, carefully lift the film and let it
sit back down under its own pressure again until you have a
bubble-free installation.
STEP 10
Use the soft edge squeegee to work any small bubbles and the edges of the film.
But if any edges are lifting slightly, do not worry, they will relax
down once the PROTECTIVE LINER is removed.
STEP 11
Once the film is installed on the glass you can then start work on
wiring the bus-bar. Carefully solder the electrical cable to the mesh
tags.There are two tags on the left hand side and two tags on the
right hand side. Solder a cable to one tag on the left (positive
connection) and one tag on the right (negative connection). The other
tags are only there as spares. You can use them to connect the cables
to a switch or transformer and test the switching from frosted to
clear. Once you have tested successfully, you can trim off the spare
mesh tags.
STEP 12
Now you can carefully remove the other protective liner.
STEP 13
Run some clear double-sided tape along the bus-bar edge to hold your
electrical cables in place while you prepare the cover trim.
STEP 14
Use Dow Corning (7091) non-acid based silicone along the bus-bar edge
to hold the protective cover trim in place. We recommend you use a
plastic cover trim.
STEP 16
Now, Congratulations! The installation is complete and you can clean
the film. For most installations we would recommend that you use a
cover trim on all edges of the film.
Implication Example:
CNC INTERLAYER TECHNOLOGY
Contact us: cnc@cncnext.com / eva@evafilm.com / benext77@gmail.com/
benext77@hotmail.com
